APW Wyott M-2000 Service Manual download pdf (Page 2)

SAFETY PRECAUTIONS

APW Wyott toasters are designed, built and sold for commercial use and should be operated by trained personal only. Make

sure all CAUTIONS, WARNINGS and operating instructions are clearly posted near each unit to insure proper operation and

reduce the chance of personal injury and/or equipment damage.

Always disconnect power before cleaning or servicing the toaster. Surfaces will remain hot after power has been removed,

allow unit to cool before cleaning or servicing. Never clean the toaster by immersing it in water. The toaster is not protected

against water jets; DO NOT CLEAN TOASTER WITH A WATER JET. Always clean equipment before first use.

Operating toaster without legs will void the warranty. Insure all accessories and exterior panels are properly installed and

adjusted before applying power and operating.

GENERAL INFORMATION

Check the rating label for your model designation and electrical rating. Rating Label is located on the bottom front of the

control panel.

Overall dimensions with feeder: 23.5"(59.7cm) W x 25.9"(65.8cm) H x 17.5"(44.5cm) D

Electrical ratings:

M2KA: 120VAC, 1800W, 60Hz

M2KH: 208-240VAC, 2880-3840W, 60Hz

Cordset Configuration:

120V: NEMA 5-15P Plug, 4 foot, 3 wire grounded cord (For Installation in Canada NEMA 5-20P plug, 6 foot cord)

208/250V: NEMA 6-20P Plug, 4 foot, 3 wire grounded cord. If the supply cord is damaged, it must be replaced by the

manufacturer or an authorized service agent or a similarly qualified person in order to avoid a hazard.

Shipping Weight:

INSTALLATION

1. Unpack Unit

Remove unit from shipping carton, unwrap loose parts and remove any packing tape, plastic wrap and nylon tie-down.

Account for the following parts:

Legs Shipped (4) in plastic bag

Butter roller & Pan (optional) In individual carton

Conveyor In individual carton

Feeder/Bun Chute Wrapped, loose in top of carton

Instruction Manual Loose in carton

Teflon Sheet Kit (optional) Loose in carton

NOTE:

Prior to initial start-up, all removable parts and the grill surface should be cleaned with warm soapy water to remove

manufacturing oils, then rinsed and dried thoroughly. Apply oil to the conveyor chain after washing. Also, for wet operation the

grill surface should be seasoned with a light coating of oil (fry oil works well) and preheated for 15-20 minutes.

2. Assemble Legs

Lay the toaster on its side and install the four adjustable legs into the threaded holes on the bottom of the toaster sides. Hand

tighten the legs by gripping the black shank and turning until it is seated firmly against the bottom of the side. Set the toaster

upright. The unit may be leveled by unscrewing the lower, chrome insert of each leg. Flats are provided on two sides of the

insert to allow use of a wrench. “Precise” leveling is not required for proper operation.

3. Conveyor Installation

The conveyor is shipped in an individual carton. Unpack the conveyor and clean and lubricate as noted.

Remove the top front panel by lifting it straight up. The bottom front panel can now be removed by lifting it straight up to

disengage the pins and rod.

Lift conveyor using “U” shaped handles on each conveyor side bracket and lower it into the two hanger brackets above the

grill plate on each side, so the four spacers on the sides of the conveyor rest on the bottom flange and the bottom spacers are

against the adjustment screws. The hanger brackets are factory adjusted. However, before reinstalling the front panels apply

power to the unit and run the conveyor to insure proper gear engagement. If gears are not properly engaged adjust the

conveyor by loosening the jam nuts on the hanger brackets and adjusting the conveyor to the correct height. Retighten jam

nuts after adjustment is complete. Reinstall front panel.

PAGE 2

1 2 3 4 5 6 7 8 9

Comments to this Manuals

No comments

APW Wyott M-2000 Service Manual Page 2

Comments to this Manuals

Related products and manuals for Toasters APW Wyott M-2000